Home
>
Beginners Guide To Acrylic
>
Beginners Guide To Acrylic: Laser Cutting Acrylic: Beginner Basics (Settings, Clean Cuts & Mistakes)
Beginners Guide To Acrylic: Laser Cutting Acrylic: Beginner Basics (Settings, Clean Cuts & Mistakes)
CMBACRYLIC
Beginners Guide
Beginners Guide · Laser Cutting
Laser Cutting Basics: Settings, Clean Cuts & Mistakes to Avoid
If you're new to laser cutting acrylic, it can feel frustrating at first. Cuts don't go all the way through, edges look messy, or settings that worked yesterday suddenly don't work today.
The truth is, acrylic is one of the best materials to work with—but only if you understand how it behaves.
This guide will walk you through the fundamentals of laser cutting acrylic, including settings, how to get clean cuts, and how to fix the most common issues beginners run into.
First things first
Start with the Right Material
Before adjusting settings, make sure you're using the right type of acrylic.
Cast Acrylic
The preferred choice for laser cutting and engraving. It cuts cleanly, produces polished edges, and engraves with a crisp, frosted look.
Extruded Acrylic
Can work, but it tends to melt more easily and doesn't engrave as cleanly.
If you're unsure about the differences, check out our Types of Acrylic Explained guide.
Dialing in
Understanding Laser Settings
Laser settings are not one-size-fits-all. They depend on your machine, material thickness, and even environmental factors.
The three main settings you'll adjust are:
Power
How strong the laser is.
Speed
How fast the laser moves.
Frequency (or PPI)
How often the laser fires.
For acrylic, the general rule is: higher power + slower speed = deeper cuts.
Start with recommended settings for your machine, then make small adjustments until you get clean results.
Pro tip: Always test on a small piece before running a full sheet.
Technique
How to Get Clean Cuts on Acrylic
One of the biggest advantages of acrylic is its ability to produce smooth, polished edges when cut correctly. To get clean cuts:
Use the correct focus
Make sure your laser is properly focused on the material. Even slight misalignment can affect cut quality.
Leave the masking on
Masking helps protect the surface from smoke marks and debris during cutting.
Use proper air assist
Air assist helps reduce flaming and keeps edges clean.
Dial in your speed and power
Too fast and it won't cut through. Too slow and you risk melting or edge flare.
Common question
Which Side of Acrylic Should You Cut?
This is one of the most common beginner questions—and the answer depends on your material.
For most standard acrylic, you can cut from either side. However, when working with specialty materials, the "presentation side" matters.
General rule
- Cut with the masking side facing up when possible
- For mirror acrylic, always engrave from the back side
- For materials with coatings or finishes, keep the finished side protected
When in doubt, think about which side you want facing outward in your final product—and protect that side during cutting.
Troubleshooting
Common Mistakes Beginners Make
Most issues come down to a few common mistakes.
Not cutting all the way through
This usually means your speed is too high or your power is too low. Slow it down slightly or increase power.
Melted or rough edges
This happens when the laser lingers too long. Increase speed slightly or reduce power.
Excessive flaming
Check your air assist and make sure your material is clean and properly masked.
Inconsistent results
Environmental factors like temperature, airflow, and even material variation can affect results. Small adjustments are normal.
Process
How to Dial in Your Settings
The key to success with acrylic is consistency and testing.
Instead of making big changes, adjust one setting at a time and observe the result. Keep notes so you can repeat successful settings later.
Every machine behaves a little differently, so your "perfect settings" will be unique to your setup.
Masking
Paper vs. Plastic Masking: What You Should Know
Acrylic typically comes with either paper or plastic masking—and while both protect the surface, they behave a little differently during cutting.
Paper masking
Often preferred because it helps reduce burn marks and is less likely to melt during cutting.
Plastic masking
Offers durability but can sometimes melt slightly into the acrylic during laser cutting, especially on smaller or more detailed cuts.
Best practice: Leave masking on during cutting to protect the surface, then remove it after for a clean finish.
At a glance
Troubleshooting Quick Guide
If something goes wrong, here's a quick way to diagnose it:
| Symptom | What to do |
|---|---|
| Didn't cut through? | Increase power or decrease speed |
| Edges look melted? | Increase speed slightly |
| Burn marks? | Check masking and airflow |
| Engraving looks weak? | Increase power or adjust speed |
Small tweaks make a big difference.
Finish
Choosing the Right Acrylic for Laser Cutting
Different finishes can affect your results and final look.
Matte acrylic is great for readability, gloss for bold color, and transparent acrylic works well for layered designs. Specialty materials like glitter, mirror, and iridescent acrylic can add dimension—but may require slight setting adjustments.
If you're deciding between finishes, our Acrylic Finish Guide is a helpful place to start.
Final thoughts
Final Thoughts
Laser cutting acrylic gets easier with practice. Once you understand how your machine interacts with the material, you'll start getting consistent, clean results.
Don't get discouraged by early mistakes—they're part of the learning process. Every adjustment you make brings you closer to dialing in your perfect settings.
With the right material, the right setup, and a little patience, acrylic can quickly become one of the most rewarding materials to work with.
Ready to cut
Grab the material for your next cut
Browse acrylic sheets in every color, finish, and thickness.
Shop acrylic sheets →
i have bn messing with lasers for over an yr i can’t find good acrylic till i found u by accident l’ll b ordering some acrylic
Is there any way for you to cut the silver mirrored acrylic to a custom size? I need 3 pieces cut to 20” wide x 28”’deep. It needs to have square corners, and needs to be 1/8” thick. Please let me know if this can be done.
Is there any way for you to cut the silver mirrored acrylic to a custom size? I need 3 pieces cut to 20” wide x 28”’deep. It needs to have square corners, and needs to be 1/8” thick. Please let me know if this can be done.
Can my xtool f1 cut this acrylic?
Does this acrylic need To be masked to cut?